HTS 7225: Flat-rolled products of other alloy steel, of a width of 600 mm or more
Heading 7225 of the Harmonized Tariff Schedule of the United States has 28 ten-digit statistical numbers. A US entry line in ACE needs the full ten digits, with the quantity in kg.
Check additional duties before you file
- Steel and aluminum articles here may carry Section 232 duties. The entry can need the Chapter 99 number, the metal value and the country where the metal was melted and poured, or smelted and cast.
- If the goods are made in China, check Section 301 duties under HTSUS heading 9903.88, on top of the general rate, and any exclusions.
| HTSUS number | Description | Unit | General rate |
|---|---|---|---|
| Of silicon electrical steel: | |||
| 7225.11.00.00 | Grain-oriented | kg | Free |
| 7225.19.00.00 | Other | kg | Free |
| 7225.30 | Other, not further worked than hot-rolled, in coils: | ||
| Of a thickness of 4.75 mm or more: | |||
| 7225.30.11 | Of tool steel | Free | |
| 7225.30.11.10 | Of high-speed steel | kg | |
| 7225.30.11.80 | Other | kg | |
| 7225.30.30 | Other | Free | |
| 7225.30.30.05 | Of high-nickel alloy steel | kg | |
| 7225.30.30.50 | Other | kg | |
| Of a thickness of less than 4.75 mm: | |||
| 7225.30.51 | Of tool steel | Free | |
| 7225.30.51.10 | Of high-speed steel | kg | |
| 7225.30.51.80 | Other | kg | |
| 7225.30.70.00 | Other | kg | Free |
| 7225.40 | Other, not further worked than hot-rolled, not in coils: | ||
| Of a thickness of 4.75 mm or more: | |||
| 7225.40.11 | Of tool steel | Free | |
| 7225.40.11.10 | Of high-speed steel | kg | |
| 7225.40.11.80 | Other | kg | |
| 7225.40.30 | Other | Free | |
| 7225.40.30.05 | Of high-nickel alloy steel | kg | |
| 7225.40.30.50 | Other | kg | |
| Of a thickness of less than 4.75 mm: | |||
| 7225.40.51 | Of tool steel | Free | |
| 7225.40.51.10 | Of high-speed steel | kg | |
| 7225.40.51.30 | Of ball-bearing steel | kg | |
| 7225.40.51.60 | Other | kg | |
| 7225.40.70.00 | Other | kg | Free |
| 7225.50 | Other, not further worked than cold-rolled (cold-reduced): | ||
| 7225.50.11 | Of tool steel | Free | |
| 7225.50.11.10 | Of high-speed steel | kg | |
| 7225.50.11.30 | Of ball-bearing steel | kg | |
| 7225.50.11.60 | Other | kg | |
| Other: | |||
| 7225.50.60.00 | Of a thickness of 4.75 mm or more | kg | Free |
| Of a thickness of less than 4.75 mm: | |||
| 7225.50.70.00 | Heat-resisting steel | kg | Free |
| 7225.50.80 | Other | Free | |
| 7225.50.80.10 | Of high-nickel alloy steel | kg | |
| 7225.50.80.80 | Other | kg | |
| Other: | |||
| 7225.91.00.00 | Electrolytically plated or coated with zinc | kg | Free |
| 7225.92.00.00 | Otherwise plated or coated with zinc | kg | Free |
| 7225.99.00 | Other | Free | |
| 7225.99.00.10 | Of high-nickel alloy steel | kg | |
| 7225.99.00.90 | Other | kg |
Common paperwork mistakes with heading 7225
- The invoice shows the exporter's own code. Only the first six digits are shared worldwide; the US number has ten. Check every line against the list above.
- The quantity is in the wrong unit. These lines report quantity in kg, which may not match the invoice's cartons, sets or pieces.
- The packing list and the bill of lading disagree on cartons or gross weight, which can lead to holds and exams.
- The manufacturer's name and address are missing, so the MID cannot be built from the documents.
Look up any ten-digit number, or read the guide to invoice and packing list mismatches.
Check the whole shipment, not one number
FreightProof reads the invoice, packing list and bill of lading together, validates every HTS number and container, builds the MIDs and flags what does not match — in about two minutes.
Data: Harmonized Tariff Schedule of the United States, US International Trade Commission. Rates are for information only.