HTS 7606: Aluminum plates, sheets and strip, of a thickness exceeding 0.2 mm
Heading 7606 of the Harmonized Tariff Schedule of the United States has 19 ten-digit statistical numbers. A US entry line in ACE needs the full ten digits, with the quantity in kg.
Check additional duties before you file
- Goods under this heading are often covered by antidumping or countervailing duty orders (aluminum sheet). Confirm scope, country and manufacturer in CBP's AD/CVD case search. A missing case number is a common reason for penalties.
- Steel and aluminum articles here may carry Section 232 duties. The entry can need the Chapter 99 number, the metal value and the country where the metal was melted and poured, or smelted and cast.
- If the goods are made in China, check Section 301 duties under HTSUS heading 9903.88, on top of the general rate, and any exclusions.
| HTSUS number | Description | Unit | General rate |
|---|---|---|---|
| Rectangular (including square): | |||
| 7606.11 | Of aluminum, not alloyed: | ||
| 7606.11.30 | Not clad | 3% | |
| 7606.11.30.30 | With a thickness of more than 6.3 mm | kg | |
| 7606.11.30.60 | With a thickness of 6.3 mm or less | kg | |
| 7606.11.60.00 | Clad | kg | 2.7% |
| 7606.12 | Of aluminum alloys: | ||
| 7606.12.30 | Not clad | 3% | |
| With a thickness of more than 6.3 mm: | |||
| 7606.12.30.15 | High-strength heat-treatable alloys of a kind described in statistical note 6 to this chapter | kg | |
| 7606.12.30.25 | Heat-treatable industrial alloys of a kind described in statistical note 7 to this chapter | kg | |
| 7606.12.30.35 | Other | kg | |
| With a thickness of 6.3 mm or less: | |||
| Aluminum can stock: | |||
| 7606.12.30.45 | Body stock | kg | |
| 7606.12.30.55 | Lid stock | kg | |
| Other: | |||
| 7606.12.30.91 | Heat-treatable industrial alloys of a kind described in statistical note 7 to this chapter | kg | |
| 7606.12.30.96 | Other | kg | |
| 7606.12.60.00 | Clad | kg | 6.5% |
| Other: | |||
| 7606.91 | Of aluminum, not alloyed: | ||
| 7606.91.30 | Not clad | 3% | |
| 7606.91.30.55 | With a thickness of more than 6.3 mm | kg | |
| 7606.91.30.95 | With a thickness of 6.3 mm or less | kg | |
| 7606.91.60 | Clad | 2.7% | |
| 7606.91.60.55 | With a thickness of more than 6.3 mm | kg | |
| 7606.91.60.95 | With a thickness of 6.3 mm or less | kg | |
| 7606.92 | Of aluminum alloys: | ||
| 7606.92.30 | Not clad | 3% | |
| 7606.92.30.25 | With a thickness of more than 6.3 mm | kg | |
| 7606.92.30.35 | With a thickness of 6.3 mm or less | kg | |
| 7606.92.60 | Clad | 6.5% | |
| 7606.92.60.55 | With a thickness of more than 6.3 mm | kg | |
| 7606.92.60.95 | With a thickness of 6.3 mm or less | kg |
Common paperwork mistakes with heading 7606
- The invoice shows the exporter's own code. Only the first six digits are shared worldwide; the US number has ten. Check every line against the list above.
- The quantity is in the wrong unit. These lines report quantity in kg, which may not match the invoice's cartons, sets or pieces.
- The packing list and the bill of lading disagree on cartons or gross weight, which can lead to holds and exams.
- The manufacturer's name and address are missing, so the MID cannot be built from the documents.
Look up any ten-digit number, or read the guide to invoice and packing list mismatches.
Check the whole shipment, not one number
FreightProof reads the invoice, packing list and bill of lading together, validates every HTS number and container, builds the MIDs and flags what does not match — in about two minutes.
Data: Harmonized Tariff Schedule of the United States, US International Trade Commission. Rates are for information only.