HTS 7214: Other bars and rods of iron or nonalloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but including those twisted after rolling
Heading 7214 of the Harmonized Tariff Schedule of the United States has 18 ten-digit statistical numbers. A US entry line in ACE needs the full ten digits, with the quantity in kg.
Check additional duties before you file
- Goods under this heading are often covered by antidumping or countervailing duty orders (steel concrete reinforcing bar). Confirm scope, country and manufacturer in CBP's AD/CVD case search. A missing case number is a common reason for penalties.
- Steel and aluminum articles here may carry Section 232 duties. The entry can need the Chapter 99 number, the metal value and the country where the metal was melted and poured, or smelted and cast.
- If the goods are made in China, check Section 301 duties under HTSUS heading 9903.88, on top of the general rate, and any exclusions.
| HTSUS number | Description | Unit | General rate |
|---|---|---|---|
| 7214.10.00.00 | Forged | kg | Free |
| 7214.20.00.00 | Concrete reinforcing bars and rods | kg | Free |
| 7214.30.00 | Other, of free-cutting steel | Free | |
| 7214.30.00.10 | Containing by weight 0.1 percent or more of lead | kg | |
| 7214.30.00.80 | Other | kg | |
| Other: | |||
| 7214.91.00 | Of rectangular (other than square) cross-section | Free | |
| Containing by weight less than 0.25 percent of carbon: | |||
| 7214.91.00.16 | With a maximum cross section less than 152 mm | kg | |
| 7214.91.00.20 | With a maximum cross section of 152 mm or more | kg | |
| 7214.91.00.60 | Containing by weight 0.25 percent or more but less than 0.6 percent of carbon | kg | |
| 7214.91.00.90 | Containing by weight 0.6 percent or more of carbon | kg | |
| 7214.99.00 | Other | Free | |
| Rounds: | |||
| Containing by weight less than 0.25 percent of carbon: | |||
| 7214.99.00.16 | With a diameter less than 76 mm | kg | |
| 7214.99.00.21 | With a diameter of 76 mm or more but not exceeding 152 mm | kg | |
| 7214.99.00.26 | With a diameter exceeding 152 mm | kg | |
| Containing by weight 0.25 percent or more but less than 0.6 percent of carbon: | |||
| 7214.99.00.31 | With a diameter less than 76 mm | kg | |
| 7214.99.00.36 | With a diameter of 76 mm or more but not exceeding 152 mm | kg | |
| 7214.99.00.40 | With a diameter exceeding 152 mm | kg | |
| 7214.99.00.45 | Containing by weight 0.6 percent or more of carbon | kg | |
| Other: | |||
| 7214.99.00.60 | Containing by weight less than 0.25 percent of carbon | kg | |
| 7214.99.00.75 | Containing by weight 0.25 percent or more but less than 0.6 percent of carbon | kg | |
| 7214.99.00.90 | Containing by weight 0.6 percent or more of carbon | kg |
Common paperwork mistakes with heading 7214
- The invoice shows the exporter's own code. Only the first six digits are shared worldwide; the US number has ten. Check every line against the list above.
- The quantity is in the wrong unit. These lines report quantity in kg, which may not match the invoice's cartons, sets or pieces.
- The packing list and the bill of lading disagree on cartons or gross weight, which can lead to holds and exams.
- The manufacturer's name and address are missing, so the MID cannot be built from the documents.
Look up any ten-digit number, or read the guide to invoice and packing list mismatches.
Check the whole shipment, not one number
FreightProof reads the invoice, packing list and bill of lading together, validates every HTS number and container, builds the MIDs and flags what does not match — in about two minutes.
Data: Harmonized Tariff Schedule of the United States, US International Trade Commission. Rates are for information only.